GPSR (Regulation 2023/988): obligations for online sellers of electrical products

Regulation (EU) 2023/988 on general product safety (GPSR) has applied since 13 December 2024, replacing Directive 2001/95/EC. For wholesalers, online shops and installers selling electrical accessories, the GPSR mainly brings new requirements for online product information and clear rules for accidents and recalls. The points below are based on the regulation text on EUR-Lex.
GPSR and the Low Voltage Directive
Most electrical equipment, such as circuit breakers, sockets, luminaires and extension leads, is covered by Union harmonisation legislation, above all the Low Voltage Directive 2014/35/EU. The GPSR does not duplicate it. Under Article 2(1):
- the GPSR applies insofar as Union law has no specific provisions with the same objective;
- for products covered by harmonisation legislation some GPSR chapters do not apply, and others apply only to aspects and risks not covered by that legislation.
In practice the rules on distance sales, accident reporting and recalls are relevant to electrical sellers too, even though electrical safety itself is assessed under the LVD and harmonised standards.
What an online listing must contain (Article 19)
| Item | Example for electrical equipment |
|---|---|
| a) Manufacturer details: name or registered trademark, postal and electronic address | Name and address of the breaker manufacturer, contact page |
| b) If the manufacturer is not established in the EU, the responsible person in the EU | Importer or authorised representative |
| c) Information identifying the product, including a picture, its type and other identifiers | Photo, catalogue number, series, type |
| d) Warnings and safety information in a language easily understood by consumers in the Member State | Note on installation by a qualified person, warnings from the instructions |
For a shop with thousands of items this means keeping complete manufacturer data, current photos and catalogue numbers. Publishing instructions and datasheets next to the product is good practice.
Distributor obligations (GPSR Article 12 and LVD Article 9)
Before making a product available, a distributor verifies that the manufacturer and, where applicable, the importer have met their obligations, including product identification, contact details and instructions and safety information. Note: under Article 2(1) GPSR, Chapter III Section 1 (including Article 12) does not apply to products covered by Union harmonisation legislation. For equipment under the Low Voltage Directive, distributor obligations follow from Article 9 of Directive 2014/35/EU (checking the CE marking, the required documents and the instructions and safety information in the local language), while GPSR Article 12 covers products outside harmonisation. Either way, good practice for a wholesaler is a goods-in check:
- manufacturer details and a type or batch identifier on the product or packaging;
- instructions in the local language included;
- no doubts about safety (damage, missing markings, suspected counterfeit).
Watch for counterfeits: modular devices and extension leads are product groups where counterfeits occur. Buy from authorised distributors and check the product markings.
Accidents and the Safety Business Gateway (Article 20)
When a product causes an accident, the manufacturer notifies the authorities through the Safety Business Gateway without undue delay after becoming aware of it. Importers and distributors who learn of an accident inform the manufacturer without undue delay. A seller who hears from a customer about an overheating socket or a smoking extension lead should therefore have a procedure for passing the information on.
Recalls: buyer rights (Articles 35–37)
- Consumers who can be identified are informed directly and without undue delay; otherwise the widest-reaching channels are used.
- The recall notice is headed "Product safety recall", describes the product and hazard, tells consumers to stop using it immediately and must not downplay the risk.
- The consumer chooses between at least two remedies: repair, replacement with a safe product or refund of the product's value, with no shipping or return costs.
A shop that keeps order history can quickly reach buyers of an affected batch, another reason to maintain accurate customer data.
Installers who sell products
An installer who buys devices and resells them to a customer as part of a job also makes a product available on the market. No online shop is needed, but the installer should buy from sources that provide manufacturer data and instructions, pass instructions and warnings to the customer, and know whom to notify about a worrying incident. Keeping purchase records with batch numbers makes it much easier to find affected customers in a recall.
Checklist for an electrical shop
- Every product page: manufacturer with address, photo, catalogue number and type.
- Warnings and instructions in the language of each country you sell to.
- Goods-in procedure in line with LVD Article 9 (electrical equipment) or GPSR Article 12 (non-harmonised products).
- Procedure for passing accident reports to the manufacturer.
- Readiness to contact buyers in a recall.
This article is for information only. The binding text is Regulation (EU) 2023/988 on EUR-Lex.
Standards and legal sources
This article is for information only. The applicable regulations and standards and the manufacturer's documentation prevail.